Device |
Trainable Digital Prop/Scene Controller |
Precision repeatability and reliability due to digital processing. No obsolete analog timers. Trained via key banger method |
Control Channels |
One |
Single control channel, but dual sets of relay contacts. |
Relay Channels |
Two |
Two independent sets of relay contacts allow for simultaneous control of high voltage (120vac) and low voltage circuits. |
Current Rating |
16-Amps total |
Each relay channel rated at 8-amps. They may be paralleled for a total current handling capacity of 16-amps, AC or DC, low voltage or 120 volt. |
Relay Life |
20,000,000 operations |
That’s more than 5,000 operations per day, 365 days per year for 10 years! |
Response Time |
1/100th of a second |
This is equivalent to 30-40 times faster than the average person can blink their eyes. |
Processor Speed |
1 MIPS |
1,000,000 instructions per second! |
Warranty |
5-Years |
Warrantied against defect in materials or workmanship for 5-years, including when used in commercial applications. |
Power |
9-14vdc, 100mA |
Current requirement higher if supplying power to anything other than a single Lights Alive trigger/sensor. 24vdc version available as special order. |
Power Out |
Two methods |
Mantis controllers supply power to all Lights Alive brand trigger/sensors via the proprietary LADC connection. Screw terminals are provided for 3rd party sensors. |
Prop Power |
Via relay contacts |
12vdc, up to a maximum of 1-amp can be supplied to solenoid valves or other relays with a simple jumper, eliminating the need for other power supplies. |
Trigger Connection |
Via LADC or screw terminals |
All Lights Alive brand triggers/sensors connect to the controller via the LADC cable which provides trigger circuitry and power. Screw terminals are provided for 3rd party triggers. |
Internal Timer |
User trainable |
Microprocessor memorizes real time training. Simply enter program mode and press CHANNEL button to activate relay. miniMANTIS will remember this routine when triggered |
Indicators |
Four |
Activity, trigger, status and LADC device present LED indicators included. |
Repeat Function? |
Yes |
Runs program once, then waits for next trigger in normal mode. In continuous mode the program will be continuously repeated. Starts automatically if trigger strapped at power up. |
Trigger Method |
Switch closure |
Compatible with all Lights-Alive brand triggers and intelligent sensors as well as any other brand device that provides simple switch closure. |
Input Isolation? |
Optical |
All Mantis controllers and intelligent sensors are equipped with optoisolators to isolate and protect the microprocessor |
LADC Technology? |
Yes |
All Mantis products are equipped with LADC (Lights Alive Direct Connect) technology. With LADC, a single quick-connect cable carries DC power and the trigger circuit to trigger/sensor. CLICK, CLICK, DONE! Screw terminals provided for connecting 3rd party triggers. |
User Controls |
Three |
TEST, CONTROL and CHANNEL |
Pluggable Connectors |
Two |
Both screw terminal connectors may be quickly unplugged and plugged into a replacement controller in the unlikely event of a problem, thus reducing down time |
Custom Configurations |
Many |
Custom configurations include, but are not limited to 24vdc operation, DC output from one or both relay contact sets, pre-programmed routines, etc. |
Build Versions |
Three |
Fully assembled units, finished boards for inclusion in your box and kits are available |
Daisy Chain |
Yes |
Multiple controllers can be daisy chained thus requiring only a single power source |
Prop Test |
Yes |
When idle, pressing CHAN will trigger relay to test prop without need to run program |
Program Protect |
Yes |
Program protect mode eliminates the possibility of accidental program erasure. Program also retained during power failure. |
Global Erase |
Yes |
Global erase is provided to erase all programming with on quick action
All specifications are subject to change without notice. 032409 |
